[PDF&VCE] Latest Released Cisco 200-125 Exam Question Free Download From Lead2pass (141-160)

2016 September Cisco Official New Released 200-125 Dumps in Lead2pass.com!

100% Free Download! 100% Pass Guaranteed!

The 200-125 braindumps are the latest, authenticated by expert and covering each and every aspect of 200-125 exam. Comparing with others, our exam questions are rich in variety. We offer PDF dumps and 200-125 VCE dumps. Welcome to choose.

Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/200-125.html

QUESTION 141
Which two statements about static NAT translations are true? (Choose two.)

A.    They allow connections to be initiated from the outside.
B.    They require no inside or outside interface markings because addresses are statically defined.
C.    They are always present in the NAT table.
D.    They can be configured with access lists, to allow two or more connections to be initiated from the outside.

Answer: AC
Explanation:
Static NAT is to map a single outside IP address to a single inside IP address. This is typically done to allow incoming connections from the outside (Internet) to the inside. Since these are static, they are always present in the NAT table even if they are not actively in use.

QUESTION 142
Which statement about access lists that are applied to an interface is true?

A.    You can place as many access lists as you want on any interface.
B.    You can apply only one access list on any interface.
C.    You can configure one access list, per direction, per Layer 3 protocol.
D.    You can apply multiple access lists with the same protocol or in different directions.

Answer: C
Explanation:
We can have only 1 access list per protocol, per direction and per interface. It means:
+ We can not have 2 inbound access lists on an interface + We can have 1 inbound and 1 outbound access list on an interface

QUESTION 143
Which item represents the standard IP ACL?

A.    access-list 110 permit ip any any
B.    access-list 50 deny 192.168.1.1 0.0.0.255
C.    access list 101 deny tcp any host 192.168.1.1
D.    access-list 2500 deny tcp any host 192.168.1.1 eq 22

Answer: B
Explanation:
The standard access lists are ranged from 1 to 99 and from 1300 to 1999 so only access list 50 is a standard access list.

QUESTION 144
A network administrator is configuring ACLs on a Cisco router, to allow traffic from hosts on networks 192.168.146.0, 192.168.147.0, 192.168.148.0, and 192.168.149.0 only. Which two ACL statements, when combined, would you use to accomplish this task? (Choose two.)

A.    access-list 10 permit ip 192.168.146.0 0.0.1.255
B.    access-list 10 permit ip 192.168.147.0 0.0.255.255
C.    access-list 10 permit ip 192.168.148.0 0.0.1.255
D.    access-list 10 permit ip 192.168.149.0 0.0.255.255
E.    access-list 10 permit ip 192.168.146.0 0.0.0.255
F.    access-list 10 permit ip 192.168.146.0 255.255.255.0

Answer: AC
Explanation:
access-list 10 permit ip 192.168.146.0 0.0.1.255 will include the 192.168.146.0 and 192.168.147.0 subnets, while access-list 10 permit ip 192.168.148.0 0.0.1.255 will include

QUESTION 145
What can be done to secure the virtual terminal interfaces on a router? (Choose two.)

A.    Administratively shut down the interface.
B.    Physically secure the interface.
C.    Create an access list and apply it to the virtual terminal interfaces with the access-group command.
D.    Configure a virtual terminal password and login process.
E.    Enter an access list and apply it to the virtual terminal interfaces using the access-class command.

Answer: DE
Explanation:
It is a waste to administratively shut down the interface. Moreover, someone can still access the virtual terminal interfaces via other interfaces ->
We can not physically secure a virtual interface because it is "virtual" -> To apply an access list to a virtual terminal interface we must use the "access-class" command. The "access-group" command is only used to apply an access list to a physical interface -> C is not correct.
The most simple way to secure the virtual terminal interface is to configure a username & password to prevent unauthorized login.

QUESTION 146
Which two commands correctly verify whether port security has been configured on port FastEthernet 0/12 on a switch? (Choose two.)

A.    SW1#show port-secure interface FastEthernet 0/12
B.    SW1#show switchport port-secure interface FastEthernet 0/12
C.    SW1#show running-config
D.    SW1#show port-security interface FastEthernet 0/12
E.    SW1#show switchport port-security interface FastEthernet 0/12

Answer: CD
Explanation:
We can verify whether port security has been configured by using the "show running-config" or "show port-security interface " for more detail.

QUESTION 147
Refer to the exhibit. The following commands are executed on interface fa0/1 of 2950Switch.
2950Switch(config-if)# switchport port-security
2950Switch(config-if)# switchport port-security mac-address sticky
2950Switch(config-if)# switchport port-security maximum 1
The Ethernet frame that is shown arrives on interface fa0/1.
What two functions will occur when this frame is received by 2950Switch? (Choose two.)

1471

A.    The MAC address table will now have an additional entry of fa0/1 FFFF.FFFF.FFFF.
B.    Only host A will be allowed to transmit frames on fa0/1.
C.    This frame will be discarded when it is received by 2950Switch.
D.    All frames arriving on 2950Switch with a destination of 0000.00aa.aaaa will be forwarded out fa0/1.
E.    Hosts B and C may forward frames out fa0/1 but frames arriving from other switches will not be forwarded
out fa0/1.
F.    Only frames from source 0000.00bb.bbbb, the first learned MAC address of 2950Switch, will be forwarded
out fa0/1.

Answer: BD
Explanation:
The configuration shown here is an example of port security, specifically port security using sticky addresses. You can use port security with dynamically learned and static MAC addresses to restrict a port’s ingress traffic by limiting the MAC addresses that are allowed to send traffic into the port. When you assign secure MAC addresses to a secure port, the port does not forward ingress traffic that has source addresses outside the group of defined addresses. If you limit the number of secure MAC addresses to one and assign a single secure MAC address, the device attached to that port has the full bandwidth of the port. Port security with sticky MAC addresses provides many of the same benefits as port security with static MAC addresses, but sticky MAC addresses can be learned dynamically. Port security with sticky MAC addresses retains dynamically learned MAC addresses during a link-down condition.

QUESTION 148
What will be the result if the following configuration commands are implemented on a Cisco switch?
Switch(config-if)# switchport port-security
Switch(config-if)# switchport port-security mac-address sticky

A.    A dynamically learned MAC address is saved in the startup-configuration file.
B.    A dynamically learned MAC address is saved in the running-configuration file.
C.    A dynamically learned MAC address is saved in the VLAN database.
D.    Statically configured MAC addresses are saved in the startup-configuration file if frames from that
address are received.
E.    Statically configured MAC addresses are saved in the running-configuration file if frames from that
address are received.

Answer: B
Explanation:
In the interface configuration mode, the command switchport port-security mac-address sticky enables sticky learning. When entering this command, the interface converts all the dynamic secure MAC addresses to sticky secure MAC addresses.

QUESTION 149
The network administrator cannot connect to Switch1 over a Telnet session, although the hosts attached to Switch1 can ping the interface Fa0/0 of the router. Given the information in the graphic and assuming that the router and Switch2 are configured properly, which of the following commands should be issued on Switch1 to correct this problem?

A.    Switch1(config)# line con0
Switch1(config-line)# password cisco
Switch1(config-line)#login
B.    Switch1(config)# interface fa0/1
Switch1(config-if)# ip address 192.168.24.3 255.255.255.0
C.    Switch1(config)# ip default-gateway 192.168.24.1
D.    Switch1(config)# interface fa0/1
Switch1(config-if)# duplex full
Switch1(config-if)# speed 100
E.    Switch1(config)# interface fa0/1
Switch1(config-if)# switchport mode trunk

Answer: C
Explanation:
Since we know hosts can reach the router through the switch, we know that connectivity, duplex. Speed, etc. are good. However, for the switch itself to reach networks outside the local one, the ip default-gateway command must be used.

QUESTION 150
Refer to the exhibit. Which of these statements correctly describes the state of the switch once the boot process has been completed?

1501

A.    As FastEthernet0/12 will be the last to come up, it will be blocked by STP.
B.    Remote access management of this switch will not be possible without configuration change.
C.    More VLANs will need to be created for this switch.
D.    The switch will need a different IOS code in order to support VLANs and STP.

Answer: B
Explanation:
Notice the line, which says "Interface VLAN1, changed state to administratively down". This shows that VLAN1 is shut down. Hence remote management of this switch is not possible unless VLAN1 is brought back up. Since VLAN1 is the only interface shown in the output, you have to assume that no other VLAN interface has been configured with an IP Address.

QUESTION 151
Refer to exhibit. A network administrator cannot establish a Telnet session with the indicated router. What is the cause of this failure?

1511
A.    A Level 5 password is not set.
B.    An ACL is blocking Telnet access.
C.    The vty password is missing.
D.    The console password is missing.

Answer: C
Explanation:
The login keyword has been set, but not password. This will result in the "password required, but none set" message to users trying to telnet to this router.

QUESTION 152
Refer to the exhibit. When running EIGRP, what is required for RouterA to exchange routing updates with RouterC?

1521

A.    AS numbers must be changed to match on all the routers
B.    Loopback interfaces must be configured so a DR is elected
C.    The no auto-summary command is needed on Router A and Router C
D.    Router B needs to have two network statements, one for each connected network

Answer: A
Explanation:
This question is to examine the understanding of the interaction between EIGRP routers. The following information must be matched so as to create neighborhood. EIGRP routers to establish, must match the following information:
1. AS Number;
2. K value.

QUESTION 153
A router has two Fast Ethernet interfaces and needs to connect to four VLANs in the local network. How can you accomplish this task, using the fewest physical interfaces and without decreasing network performance?

A.    Use a hub to connect the four VLANS with a Fast Ethernet interface on the router.
B.    Add a second router to handle the VLAN traffic.
C.    Add two more Fast Ethernet interfaces.
D.    Implement a router-on-a-stick configuration.

Answer: D
Explanation:
A router on a stick allows you to use sub-interfaces to create multiple logical networks on a single physical interface.

QUESTION 154
Users on the 172.17.22.0 network cannot reach the server located on the 172.31.5.0 network. The network administrator connected to router Coffee via the console port, issued the show ip route command, and was able to ping the server.

1541
Based on the output of the show ip route command and the topology shown in the graphic, what is the cause of the failure?

A.    The network has not fully converged.
B.    IP routing is not enabled.
C.    A static route is configured incorrectly.
D.    The FastEthernet interface on Coffee is disabled.
E.    The neighbor relationship table is not correctly updated.
F.    The routing table on Coffee has not updated .

Answer: C
Explanation:
The default route or the static route was configured with incorrect next-hop ip address 172.19.22.2 The correct ip address will be 172.18.22.2 to reach server located on 172.31.5.0 network. Ip route 0.0.0.0 0.0.0.0 172.18.22.2

QUESTION 155
A network administrator is trying to add a new router into an established OSPF network. The networks attached to the new router do not appear in the routing tables of the other OSPF routers. Given the information in the partial configuration shown below, what configuration error is causing this problem?
Router(config)# router ospf 1
Router(config-router)# network 10.0.0.0 255.0.0.0 area 0

A.    The process id is configured improperly.
B.    The OSPF area is configured improperly.
C.    The network wildcard mask is configured improperly.
D.    The network number is configured improperly.
E.    The AS is configured improperly.
F.    The network subnet mask is configured improperly.

Answer: C
Explanation:
When configuring OSPF, the mask used for the network statement is a wildcard mask similar to an access list. In this specific example, the correct syntax would have been "network 10.0.0.0 0.0.0.255 area 0."

QUESTION 156
Which Cisco Catalyst feature automatically disables the port in an operational PortFast upon receipt of a BPDU?

A.    BackboneFast
B.    UplinkFast
C.    Root Guard
D.    BPDU Guard
E.    BPDU Filter

Answer: D
Explanation:
We only enable PortFast feature on access ports (ports connected to end stations). But if someone does not know he can accidentally plug that port to another switch and a loop may occur when BPDUs are being transmitted and received on these ports. With BPDU Guard, when a PortFast receives a BPDU, it will be shut down to prevent a loop.

QUESTION 157
When you are troubleshooting an ACL issue on a router, which command would you use to verify which interfaces are affected by the ACL?

A.    show ip access-lists
B.    show access-lists
C.    show interface
D.    show ip interface
E.    list ip interface

Answer: D
Explanation:
Incorrect answer:
show ip access-lists does not show interfaces affected by an ACL.

QUESTION 158
Host 1 is trying to communicate with Host 2. The e0 interface on Router C is down. Which of the following are true? (Choose two.)

1581

A.    Router C will use ICMP to inform Host 1 that Host 2 cannot be reached.
B.    Router C will use ICMP to inform Router B that Host 2 cannot be reached.
C.    Router C will use ICMP to inform Host 1, Router A, and Router B that Host 2 cannot be reached.
D.    Router C will send a Destination Unreachable message type.
E.    Router C will send a Router Selection message type.
F.    Router C will send a Source Quench message type.

Answer: AD
Explanation:
Host 1 is trying to communicate with Host 2. The e0 interface on Router C is down. Router C will send ICMP packets to inform Host 1 that Host 2 cannot be reached.

QUESTION 159
Refer to the exhibit. When running EIGRP, what is required for RouterA to exchange routing updates with RouterC?

1591

A.    AS numbers must be changed to match on all the routers
B.    Loopback interfaces must be configured so a DR is elected
C.    The no auto-summary command is needed on Router A and Router C
D.    Router B needs to have two network statements, one for each connected network

Answer: A
Explanation:
This question is to examine the understanding of the interaction between EIGRP routers. The following information must be matched so as to create neighborhood. EIGRP routers to establish, must match the following information:
1. AS Number;
2. K value.

QUESTION 160
Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13. An 802.1Q trunk is configured between the two switches. On CAT1, VLAN 10 is chosen as native, but on CAT2 the native VLAN is not specified. What will happen in this scenario?

A.    802.1Q giants frames could saturate the link.
B.    VLAN 10 on CAT1 and VLAN 1 on CAT2 will send untagged frames.
C.    A native VLAN mismatch error message will appear.
D.    VLAN 10 on CAT1 and VLAN 1 on CAT2 will send tagged frames.

Answer: C
Explanation:
A "native VLAN mismatch" error will appear by CDP if there is a native VLAN mismatch on an 802.1Q link. "VLAN mismatch" can cause traffic from one vlan to leak into another vlan.

Cisco 200-125 is often called the hardest of all Cisco exams. Lead2pass helps you kill the Cisco 200-125 exam challenge and achieve the perfect passing score with its latest practice test, packed into the revolutionary interactive VCE. This is the best way to prepare and pass the 200-125 exam.

200-125 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDbnNGVlNHTzJjcWc

2016 Cisco 200-125 exam dumps (All 545 Q&As) from Lead2pass:

http://www.lead2pass.com/200-125.html [100% Exam Pass Guaranteed]